Custom

Features:Tinned Copper material for EMI, RFI and ESD ProtectionFlexible and expandable braid design.For automotive and industrial use.Suitable for use in shielding electric cable from abrasion and radio frequency interferenceGreater than 99 percent pure copperUninsulated braided strand wire with tin plated coatingResistant to failure from flexingMeets QQ-W-343 standards for uninsulated annealed copper wireFlame Rated: VW-1 | For automotive and industrial use: engine tubes and hoses, cable and wire protection | Cut with shearsRoHS CompliantOur metal braid sleeving is made from tinned copper which provides great EMI, RFI and ESD protection as well as cut and abrasion resistance. Strong metal fibers made from tinned copper create our Metal Braid Sleeving that can be used in automotive applications to dress-up engines, hose support or wire protection. With a flexible weave, can easily be cut with shears, covering cables, hoses, tubes and more… it can be quickly installed for that custom professional look.Material: Tinned Copper MonofilamentThickness: 0.12mmMelt Point: 1084°C RoHS Compliant VW-1 RatingWorking Range: -60°C – 200°CThis tin-plated copper braid is suitable for use in shielding electric cable from abrasion and radio frequency interference.This braided copper wire is annealed for improved ductility and meets the QQ-W-343 specification for uninsulated wire.This copper braid is suitable for use in wire shielding applications such as in coaxial cable.Electrical wire carries an electric current or grounds an electrical device. The amount of current a wire can carry is proportional to its size (gauge), and the wire is generally sheathed with coatings and coverings to insulate and protect it from moisture, chemicals, heat, and abrasion. Copper is the primary material for electrical wire, but alloys are sometimes used to increase its strength or its resistance to chemicals and the environment. Wire can be composed of a single strand or of many smaller strands, depending on its use, and is typically annealed to improve its ductility. Electrical wire is commonly used in industrial, electronic, and automotive applications. Strong metal fibers made from tinned copper create our Metal Braided Sleeving that can be used in automotive applications to dress-up engines, hose support or wire protection. The properties of Tinned Copper Metal Braided Sleeving not only protects against cuts and abrasion, but also EMI, RFI and ESD. With a flexible weave, affordable prices and can easily be cut with shears, covering cables, hoses, tubes and more can be quickly installed for that custom professional look.1/8″Wide(0.08″Dia) tinned copper braid sleeving is made from 16 strands,each strand consists of 4 wires(0.12mm),Mesh per inch:91/4″Wide(0.16″Dia) tinned copper braid sleeving is made from 24 strands,each strand consists of 8 wires(0.12mm),Mesh per inch:75/16″Wide(0.20″Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 6 wires(0.12mm),Mesh per inch:71/2″Wide(0.32″Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 10 wires(0.12mm),Mesh per inch:711/16″Wide(0.44″Dia) tinned copper braid sleeving is made from 72 strands,each strand consists of 7 wires(0.12mm),Mesh per inch:7 stop an electrical whine in car stereo,prevent RF interference on a car ignition system,shield wiring in a van conversionhelp keep speakers from picking up short wave ham radiostop getting interference in speaker system from power wiresstop interference on FM radio from other electronics in the home (modems, game consoles, etc)shield the wire from EMI in audio amplifiereliminate emi from phono amp stage,isolate power cablesused it for Guitar Pick-Up lead shieldingIt provides a “Faraday cage”,if there is the Ham operation close by,you may have to also protect your RCA wires delivering signal to the receiver/amplifier from the DVD,CD,or other sourcesIt works beautifully for “shielding” long runs of low voltage/amperage signal wiring.Just be sure to properly solder to true/common Ground at both ends of run.In essence, a “Faraday Tube” or a “Faraday Tunnel”!good to wrap over an ethernet cable to prevent interferenceshield 50 ohm coax to stop rf interference from penetrating the coaxshield a webcam wire that is getting electrical interferenceshield from electrical wave interferenceshield RCA and power cablesshield custom made AC power cords.shield from unwanted ‘noise’ or voltage leakThe braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.you can use it as a shield from electromagnetic force (EMF), or you can use it as a grounduse on a boat or other vehicle, the copper shield as a ground for low voltage wiringshield an uninsulated braided ground strap that is receiving emiuse it to shield guitar wiring. Since the goal for any electric guitar is to achieve zero hum (interference) in your output signal, always ground your shielding or else you may find you have even more humming. Keep the shielding away from contacting any of the pots positive/negative lugs. Just a clean ground wire from the shielding to the back of volume pot if that’s what you’re using for your central ground.used by putting the wire inside and it is properly grounded rfi can’t get induced or releasedused it to protect wires from a cat chewing on them,used this type of braid to shield cables all the time,at least 60 dB if properly grounded on at least one end,Dont put too large of a cable through it such that holes appear between the braids that let RF through.Can be used as common ground straps, earthing cables and current transmission leads, and where vibrations are unavoidable for high flexibility and connections with low contact and resistance.Our Earthing braid connections are a reliable and convenient grounding solution for applications that require flexibility and durability.Our earthing braids are UL certified and can be used for all grounding applications.good to wrap over an ethernet cable to prevent interferencetin copper braided sleeving can cover motorcycle cables for aesthetic purposes and EMI protectionCould thread wires through the braid,Probably have better luck using a thin rod to pull the wires through the braid. Pushing the wires through the braid more than a few inches could be problematicshield a webcam wire that is getting electrical interferencestop getting interference in speaker system from power wiresshield from electrical wave interferencestop interference on FM radio from other electronics in the home (modems, game consoles, est)shield 50 ohm coax to stop rf interference from penetrating the coaxgood to wrap over an ethernet cable to prevent interferenceThe braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.shielding RF interference on a car ignition systemThis is a finely stranded tinned Copper braided sleeve. The dense braid yields better than 90% coverage. Great for RFI/EMI shielding on wire, or cables.The primary use of wire sleeving braid is to provide sensitive cables with an EMC screen to shield them against electromagnetic, electrostatic and radio frequency interface.Optimum screening performance is obtained using copper wire braid that can also be used for earth continuity purposes.Tin Plated copper is suitable for use at elevated temperatures and for harsh environments or where abrasion is likely to be encountered PaymentWe accept Paypal/Credit Card payment through Ebay Checkout ONLY. .Payment must be received within 7 days (from the auction ended date).Paypal buyers must have a confirmed address as the registered shipping address. Buyer must use checkout to complete the transaction. Otherwise, it might delay the ordering shipping timeShippingAll Of Our Item will be sent via USPS.24~48hours Shipped: We will ship your order out within 24~48 hours.Local Pickup :We offer Local Pickup with free shipping，you can get your item directly from our warehouse.ReturnsWe are offering 30 days return policy for any defect item.Please contact us for help and return details.All damaged packages must be reported after receiving 5 days.No claims whatsoever will be accepted if the damage was caused by customer’s abuse, negligence, or incorporated installationReturn items must be in original box and include all of the original accessories.Customer ServiceOur working time: 9:00am-6:00pm(Monday to Friday),Please feel free to contact us if you have any question.FeedbackYour Satisfaction is the best feedback for us,hope give us five stars. It is very appreciated if you can write a positive review for us.

Features:Tinned Copper material for EMI, RFI and ESD ProtectionFlexible and expandable braid design.For automotive and industrial use.Suitable for use in shielding electric cable from abrasion and radio frequency interferenceGreater than 99 percent pure copperUninsulated braided strand wire with tin plated coatingResistant to failure from flexingMeets QQ-W-343 standards for uninsulated annealed copper wireFlame Rated: VW-1 | For automotive and industrial use: engine tubes and hoses, cable and wire protection | Cut with shearsRoHS CompliantOur metal braid sleeving is made from tinned copper which provides great EMI, RFI and ESD protection as well as cut and abrasion resistance. Strong metal fibers made from tinned copper create our Metal Braid Sleeving that can be used in automotive applications to dress-up engines, hose support or wire protection. With a flexible weave, can easily be cut with shears, covering cables, hoses, tubes and more… it can be quickly installed for that custom professional look.Material: Tinned Copper MonofilamentThickness: 0.12mmMelt Point: 1084°C RoHS Compliant VW-1 RatingWorking Range: -60°C – 200°CThis tin-plated copper braid is suitable for use in shielding electric cable from abrasion and radio frequency interference.This braided copper wire is annealed for improved ductility and meets the QQ-W-343 specification for uninsulated wire.This copper braid is suitable for use in wire shielding applications such as in coaxial cable.Electrical wire carries an electric current or grounds an electrical device. The amount of current a wire can carry is proportional to its size (gauge), and the wire is generally sheathed with coatings and coverings to insulate and protect it from moisture, chemicals, heat, and abrasion. Copper is the primary material for electrical wire, but alloys are sometimes used to increase its strength or its resistance to chemicals and the environment. Wire can be composed of a single strand or of many smaller strands, depending on its use, and is typically annealed to improve its ductility. Electrical wire is commonly used in industrial, electronic, and automotive applications. Strong metal fibers made from tinned copper create our Metal Braided Sleeving that can be used in automotive applications to dress-up engines, hose support or wire protection. The properties of Tinned Copper Metal Braided Sleeving not only protects against cuts and abrasion, but also EMI, RFI and ESD. With a flexible weave, affordable prices and can easily be cut with shears, covering cables, hoses, tubes and more can be quickly installed for that custom professional look.1/8″Wide(0.08″Dia) tinned copper braid sleeving is made from 16 strands,each strand consists of 4 wires(0.12mm),Mesh per inch:91/4″Wide(0.16″Dia) tinned copper braid sleeving is made from 24 strands,each strand consists of 8 wires(0.12mm),Mesh per inch:75/16″Wide(0.20″Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 6 wires(0.12mm),Mesh per inch:71/2″Wide(0.32″Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 10 wires(0.12mm),Mesh per inch:711/16″Wide(0.44″Dia) tinned copper braid sleeving is made from 72 strands,each strand consists of 7 wires(0.12mm),Mesh per inch:7 stop an electrical whine in car stereo,prevent RF interference on a car ignition system,shield wiring in a van conversionhelp keep speakers from picking up short wave ham radiostop getting interference in speaker system from power wiresstop interference on FM radio from other electronics in the home (modems, game consoles, etc)shield the wire from EMI in audio amplifiereliminate emi from phono amp stage,isolate power cablesused it for Guitar Pick-Up lead shieldingIt provides a “Faraday cage”,if there is the Ham operation close by,you may have to also protect your RCA wires delivering signal to the receiver/amplifier from the DVD,CD,or other sourcesIt works beautifully for “shielding” long runs of low voltage/amperage signal wiring.Just be sure to properly solder to true/common Ground at both ends of run.In essence, a “Faraday Tube” or a “Faraday Tunnel”!good to wrap over an ethernet cable to prevent interferenceshield 50 ohm coax to stop rf interference from penetrating the coaxshield a webcam wire that is getting electrical interferenceshield from electrical wave interferenceshield RCA and power cablesshield custom made AC power cords.shield from unwanted ‘noise’ or voltage leakThe braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.you can use it as a shield from electromagnetic force (EMF), or you can use it as a grounduse on a boat or other vehicle, the copper shield as a ground for low voltage wiringshield an uninsulated braided ground strap that is receiving emiuse it to shield guitar wiring. Since the goal for any electric guitar is to achieve zero hum (interference) in your output signal, always ground your shielding or else you may find you have even more humming. Keep the shielding away from contacting any of the pots positive/negative lugs. Just a clean ground wire from the shielding to the back of volume pot if that’s what you’re using for your central ground.used by putting the wire inside and it is properly grounded rfi can’t get induced or releasedused it to protect wires from a cat chewing on them,used this type of braid to shield cables all the time,at least 60 dB if properly grounded on at least one end,Dont put too large of a cable through it such that holes appear between the braids that let RF through.Can be used as common ground straps, earthing cables and current transmission leads, and where vibrations are unavoidable for high flexibility and connections with low contact and resistance.Our Earthing braid connections are a reliable and convenient grounding solution for applications that require flexibility and durability.Our earthing braids are UL certified and can be used for all grounding applications.good to wrap over an ethernet cable to prevent interferencetin copper braided sleeving can cover motorcycle cables for aesthetic purposes and EMI protectionCould thread wires through the braid,Probably have better luck using a thin rod to pull the wires through the braid. Pushing the wires through the braid more than a few inches could be problematicshield a webcam wire that is getting electrical interferencestop getting interference in speaker system from power wiresshield from electrical wave interferencestop interference on FM radio from other electronics in the home (modems, game consoles, est)shield 50 ohm coax to stop rf interference from penetrating the coaxgood to wrap over an ethernet cable to prevent interferenceThe braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.shielding RF interference on a car ignition systemThis is a finely stranded tinned Copper braided sleeve. The dense braid yields better than 90% coverage. Great for RFI/EMI shielding on wire, or cables.The primary use of wire sleeving braid is to provide sensitive cables with an EMC screen to shield them against electromagnetic, electrostatic and radio frequency interface.Optimum screening performance is obtained using copper wire braid that can also be used for earth continuity purposes.Tin Plated copper is suitable for use at elevated temperatures and for harsh environments or where abrasion is likely to be encountered PaymentWe accept Paypal/Credit Card payment through Ebay Checkout ONLY. .Payment must be received within 7 days (from the auction ended date).Paypal buyers must have a confirmed address as the registered shipping address. Buyer must use checkout to complete the transaction. Otherwise, it might delay the ordering shipping timeShippingAll Of Our Item will be sent via USPS.24~48hours Shipped: We will ship your order out within 24~48 hours.Local Pickup :We offer Local Pickup with free shipping，you can get your item directly from our warehouse.ReturnsWe are offering 30 days return policy for any defect item.Please contact us for help and return details.All damaged packages must be reported after receiving 5 days.No claims whatsoever will be accepted if the damage was caused by customer’s abuse, negligence, or incorporated installationReturn items must be in original box and include all of the original accessories.Customer ServiceOur working time: 9:00am-6:00pm(Monday to Friday),Please feel free to contact us if you have any question.FeedbackYour Satisfaction is the best feedback for us,hope give us five stars. It is very appreciated if you can write a positive review for us.

Features:Tinned Copper material for EMI, RFI and ESD ProtectionFlexible and expandable braid design.For automotive and industrial use.Suitable for use in shielding electric cable from abrasion and radio frequency interferenceGreater than 99 percent pure copperUninsulated braided strand wire with tin plated coatingResistant to failure from flexingMeets QQ-W-343 standards for uninsulated annealed copper wireFlame Rated: VW-1 | For automotive and industrial use: engine tubes and hoses, cable and wire protection | Cut with shearsRoHS CompliantOur metal braid sleeving is made from tinned copper which provides great EMI, RFI and ESD protection as well as cut and abrasion resistance. Strong metal fibers made from tinned copper create our Metal Braid Sleeving that can be used in automotive applications to dress-up engines, hose support or wire protection. With a flexible weave, can easily be cut with shears, covering cables, hoses, tubes and more… it can be quickly installed for that custom professional look.Material: Tinned Copper MonofilamentThickness: 0.12mmMelt Point: 1084°C RoHS Compliant VW-1 RatingWorking Range: -60°C – 200°CThis tin-plated copper braid is suitable for use in shielding electric cable from abrasion and radio frequency interference.This braided copper wire is annealed for improved ductility and meets the QQ-W-343 specification for uninsulated wire.This copper braid is suitable for use in wire shielding applications such as in coaxial cable.Electrical wire carries an electric current or grounds an electrical device. The amount of current a wire can carry is proportional to its size (gauge), and the wire is generally sheathed with coatings and coverings to insulate and protect it from moisture, chemicals, heat, and abrasion. Copper is the primary material for electrical wire, but alloys are sometimes used to increase its strength or its resistance to chemicals and the environment. Wire can be composed of a single strand or of many smaller strands, depending on its use, and is typically annealed to improve its ductility. Electrical wire is commonly used in industrial, electronic, and automotive applications. Strong metal fibers made from tinned copper create our Metal Braided Sleeving that can be used in automotive applications to dress-up engines, hose support or wire protection. The properties of Tinned Copper Metal Braided Sleeving not only protects against cuts and abrasion, but also EMI, RFI and ESD. With a flexible weave, affordable prices and can easily be cut with shears, covering cables, hoses, tubes and more can be quickly installed for that custom professional look.1/8″Wide(0.08″Dia) tinned copper braid sleeving is made from 16 strands,each strand consists of 4 wires(0.12mm),Mesh per inch:91/4″Wide(0.16″Dia) tinned copper braid sleeving is made from 24 strands,each strand consists of 8 wires(0.12mm),Mesh per inch:75/16″Wide(0.20″Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 6 wires(0.12mm),Mesh per inch:71/2″Wide(0.32″Dia) tinned copper braid sleeving is made from 48 strands,each strand consists of 10 wires(0.12mm),Mesh per inch:711/16″Wide(0.44″Dia) tinned copper braid sleeving is made from 72 strands,each strand consists of 7 wires(0.12mm),Mesh per inch:7 stop an electrical whine in car stereo,prevent RF interference on a car ignition system,shield wiring in a van conversionhelp keep speakers from picking up short wave ham radiostop getting interference in speaker system from power wiresstop interference on FM radio from other electronics in the home (modems, game consoles, etc)shield the wire from EMI in audio amplifiereliminate emi from phono amp stage,isolate power cablesused it for Guitar Pick-Up lead shieldingIt provides a “Faraday cage”,if there is the Ham operation close by,you may have to also protect your RCA wires delivering signal to the receiver/amplifier from the DVD,CD,or other sourcesIt works beautifully for “shielding” long runs of low voltage/amperage signal wiring.Just be sure to properly solder to true/common Ground at both ends of run.In essence, a “Faraday Tube” or a “Faraday Tunnel”!good to wrap over an ethernet cable to prevent interferenceshield 50 ohm coax to stop rf interference from penetrating the coaxshield a webcam wire that is getting electrical interferenceshield from electrical wave interferenceshield RCA and power cablesshield custom made AC power cords.shield from unwanted ‘noise’ or voltage leakThe braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.you can use it as a shield from electromagnetic force (EMF), or you can use it as a grounduse on a boat or other vehicle, the copper shield as a ground for low voltage wiringshield an uninsulated braided ground strap that is receiving emiuse it to shield guitar wiring. Since the goal for any electric guitar is to achieve zero hum (interference) in your output signal, always ground your shielding or else you may find you have even more humming. Keep the shielding away from contacting any of the pots positive/negative lugs. Just a clean ground wire from the shielding to the back of volume pot if that’s what you’re using for your central ground.used by putting the wire inside and it is properly grounded rfi can’t get induced or releasedused it to protect wires from a cat chewing on them,used this type of braid to shield cables all the time,at least 60 dB if properly grounded on at least one end,Dont put too large of a cable through it such that holes appear between the braids that let RF through.Can be used as common ground straps, earthing cables and current transmission leads, and where vibrations are unavoidable for high flexibility and connections with low contact and resistance.Our Earthing braid connections are a reliable and convenient grounding solution for applications that require flexibility and durability.Our earthing braids are UL certified and can be used for all grounding applications.good to wrap over an ethernet cable to prevent interferencetin copper braided sleeving can cover motorcycle cables for aesthetic purposes and EMI protectionCould thread wires through the braid,Probably have better luck using a thin rod to pull the wires through the braid. Pushing the wires through the braid more than a few inches could be problematicshield a webcam wire that is getting electrical interferencestop getting interference in speaker system from power wiresshield from electrical wave interferencestop interference on FM radio from other electronics in the home (modems, game consoles, est)shield 50 ohm coax to stop rf interference from penetrating the coaxgood to wrap over an ethernet cable to prevent interferenceThe braided metal shielding is used for EMI/RFI interference shielding over electronic signal wiring.shielding RF interference on a car ignition systemThis is a finely stranded tinned Copper braided sleeve. The dense braid yields better than 90% coverage. Great for RFI/EMI shielding on wire, or cables.The primary use of wire sleeving braid is to provide sensitive cables with an EMC screen to shield them against electromagnetic, electrostatic and radio frequency interface.Optimum screening performance is obtained using copper wire braid that can also be used for earth continuity purposes.Tin Plated copper is suitable for use at elevated temperatures and for harsh environments or where abrasion is likely to be encountered PaymentWe accept Paypal/Credit Card payment through Ebay Checkout ONLY. .Payment must be received within 7 days (from the auction ended date).Paypal buyers must have a confirmed address as the registered shipping address. Buyer must use checkout to complete the transaction. Otherwise, it might delay the ordering shipping timeShippingAll Of Our Item will be sent via USPS.24~48hours Shipped: We will ship your order out within 24~48 hours.Local Pickup :We offer Local Pickup with free shipping，you can get your item directly from our warehouse.ReturnsWe are offering 30 days return policy for any defect item.Please contact us for help and return details.All damaged packages must be reported after receiving 5 days.No claims whatsoever will be accepted if the damage was caused by customer’s abuse, negligence, or incorporated installationReturn items must be in original box and include all of the original accessories.Customer ServiceOur working time: 9:00am-6:00pm(Monday to Friday),Please feel free to contact us if you have any question.FeedbackYour Satisfaction is the best feedback for us,hope give us five stars. It is very appreciated if you can write a positive review for us.